Voltage Data Logger Archives - rapid-tech

Kyoritsu 5020 TRMS 3-Channel Current / Voltage Data Logger

Mike — Thu, 24 May 2018 15:39:29 +0000

Kyoritsu 5020 TRMS 3-Channel Current / Voltage Data Logger Features:

Power Quality Analysis: Reference voltage, Swell, Dip, Short power Interruptions.
Variation of the measured voltage and current data can be confirmed simultaneously on the PC display monitor.
Large capacity for storing 60,000 data points when 1 channel is used, and when all the three channels are used, 20,000 data points per channel can be recorded.
Lowpass Filter will filter out the harmonics (cutoff frequency = approx. 160Hz)
LED flickers when the preset current / voltage value is exceeded

The following can be displayed: number of recorded data points, (max+ min+ peak) value for each channel complete with time/date information in the Normal recording mode. (Detected values (i.e. when values are outside preset limits ) can be displayed in other recording modes)
The last 10 recorded data points including time/date can be recalled on the logger display
Selection of One-time mode or Endless mode:
One-time on: Recording will stop when memory is used up
One-time off: Overwrite the old data, and store the latest data
Non Volatile Memory: Recorded data will be retained even if the batteries are exhausted or replaced due to the presence of a nonvolatile memory (guaranteed for 10 years)
Battery power indicator: Indicates battery voltage in 4-levels (It is possible to use the logger for a further approx. 24 hours even after the warming symbol is flashing)
User-friendly PC software “KEW LOG Soft 2” is supplied
Permits editing, analysis and graphical display of data.
Recorded data is downloadable onto a PC via USB cable.
Simplified Power Integration: (The “KEW LOG Soft 2” uses current and voltage recorded to calculate the integral power consumption).

Kyoritsu 5020 TRMS 3-Channel Data Logger Specifications:

Normal Recording Mode
(AC 50/60Hz, Sine wave, Input: 10% or more of the range at CH1)

Range	RMS Accuracy
100.0mA	±2.0%rdg±0.9%f.s.+ Accuracy of Sensor
Other ranges	±1.5%rdg±0.7%f.s.+ Accuracy of Sensor
Crest Factor	2.5 or less: RMS accuracy (sine) + 2%rdg + 1%f.s.

*Max, Min and Instant Peak values in Normal Recording mode are just reference values:
their accuracies aren’t guaranteed.

Trigger Recording Mode (AC 50/60Hz sine wave)

Range	Accuracy
100.0mA	±3.5%rdg±2.2%f.s.+ Accuracy of Sensor
Other ranges	±3.0%rdg±2.0%f.s.+ Accuracy of Sensor

Capture Recording Mode

Range	Accuracy
100.0mA	±3.0%rdg±1.7%f.s.+ Accuracy of Sensor
Other ranges	±2.5%rdg±1.5%f.s.+ Accuracy of Sensor

Recording mode	Normal, Trigger, Capture, Power Quality Analysis
Operating system	Successive Approximation (CH1 single synchronized sampling)
Rated max. working voltage	AC 9.9Vrms, 14V peak value
Number of input channel	3ch
Measuring method	True RMS
RMS measuring interval	approx. 100ms
Sampling interval	Normal/Trigger mode : approx. 1.65ms/CH Capture mode : approx. 0.55ms (waveform: at every 1.1ms) P.Q.A. mode : approx. 0.55ms
Low battery warning	Battery mark display (in 4 levels)
Over-range indication	“OL” mark is displayed when exceeding the measuring range
Auto power off	Power-off function operates automatically after a switch remains for 3min. (when recording is stopped)
Possible measurement time	Approx. 10 days (with alkaline LR6 batteries)
Applicable standards	IEC 61010-1:2001 CAT III 300V Pollution degree2 IEC 61326 (EMC standard)
Dimensions	111(L)×60(W)×42(D)mm
Weight	Approx. 265g
Included Accessories	Alkaline battery LR6×4pcs, 9118 (Carrying case) PC software “KEW LOG Soft 2”, 7148 (USB cable) Instruction manual, Quick manual, Install manual, USB Notice sheet
Optional Accessories	8146/8147/8148 (Leakage & Load current Clamp Sensor), 8121/8122/8123 (Load current Clamp Sensor), 8129/8130 (Flexible Clamp Sensor), 8309 (Voltage Sensor: only KEW 5020), 8320 (AC Adapter), 9135 (Carrying bag), 9119 (Hard carry case), 7185 (Extension cable for sensor)

The post Kyoritsu 5020 TRMS 3-Channel Current / Voltage Data Logger appeared first on rapid-tech.

Extech DL160 Dual Input True RMS AC Voltage/Current Datalogger

Mike — Mon, 11 Jul 2016 11:56:21 +0000

Datalog up to 256,000 readings with user programmable sample rate

The Extech DL160 is a Dual Input True RMS AC Voltage/Current Data logger. Simultaneously data log 2 channels of up to 256,000 readings of TRMS AC Voltage (600V) or Current (200A) or one AC Voltage and one AC Current input with a user programmable sample rate from 1 second to 24 hours. LCD displays time/date, current reading, and min/max.

DL160 Datasheet

DL160 User Manual

The post Extech DL160 Dual Input True RMS AC Voltage/Current Datalogger appeared first on rapid-tech.

HT Italia XL424 True-Rms AC Three-Phase Voltage Logger

Mike — Sat, 16 Apr 2016 23:58:07 +0000

The HT Italia XL424 can perform measurements and recording of True-Rms AC voltage up to 600 volts in a three phase three-wire system. Applications include evaluation of network voltages and unbalanced loads etc. The instrument is contained in a safety IP65 case with built-in test leads and safety alligator clips for voltage measurements. The system can record for a very long time, up to around 90 days. With DATALINK Windows software supplied with the model, the recorded data is easily downloaded to a PC for analysis.

HT Italia XL424 Functions:

True-rms AC voltage measurement up to 600V.
Recording with sampling programmable period.
Manual activation of recording.
Low battery indication.
LED indication of any operation.
RS-232 interface.
Data maintained without batteries.
Programming with DATALINK software.

Included Accessories

Set of two alligator clips, KITXL423C.
RS-232 serial cable, type C2004.
Adhesive Velcro for fixing.
Carrying bag, type BORSA2000.
User’s manual.

Specifications (accuracy stated at 23°C ±5°C ±(% of rdg + number of digits), < 60% R.H.)
Measurement Range	0 Volts to 600 Volts
Resolution	0.1 Volt
Accuracy	±(1.0% of reading + 2 digits)
Working Frequency	50/60Hz ±6%
Type of Measurement	True Rms
Bandwidth	3200Hz
Maximum Crest Factor	3
Note: meter consider null readings < 2 volts

General Specifications
Sampling Rate	64 point, 20ms for each sampling period
Sampling Period	1 sec, 6 sec, 30 sec, 1 min, 5 min
Memory Capacity	1 Mbyte Life in days (depending on batteries life): 1.5 days/1 sec; 8 days/6 sec; 42 days/30 sec; 91 days/1 min; 455 days/ 5 min
Computer Interface	RS-232
Operating Temperature/Humidity	-20°C to 60°C; 0 to 100% R.H. (RS-232 connector closed)
Storage Temperature	-20°C to 60°C; 0 to 100% R.H. (RS-232 connector closed)
Insulation	class 2 (double insulation)
Protection Degree	IP65 (RS-232 connector closed)
Maximum Altitude	2000 meters

Reference Standards	LVD: IEC/EN 61010-1 CAT III 1000V (to ground), CAT IV 600V (to ground)
Reference Standards	EMC: IEC/EN 61326 (1997) +A1 (1998) +A2 (2001)

Power Supply	2 x 1.5 volt type ‘AA’ alkaline batteries type LR6, AM3, MN1500
Battery Life	6 months
Dimensions	120mm (L) x 80mm (W) x 43mm (D)
Test Lead Length	2.6 meters
Weight	500g (with internal batteries)

The post HT Italia XL424 True-Rms AC Three-Phase Voltage Logger appeared first on rapid-tech.

HT Italia XL423 True-Rms AC Single-Phase Voltage Logger

Mike — Sat, 16 Apr 2016 23:52:46 +0000

The HT Italia XL423 can perform measurements and recording of True-Rms AC voltage up to 600 volts in a single phase system. Applications include evaluation of network voltages and unbalanced loads etc. The instrument is contained in a safety IP65 case with built-in test leads and safety alligator clips for voltage measurements. The system can record for a very long time, up to around a year. With DATALINK Windows software supplied with the model, the recorded data is easily downloaded to a PC for analysis.

HT Italia XL423 Functions:

True-rms AC voltage measurement up to 600V.
Recording with sampling programmable period.
Manual activation of recording.
Low battery indication.
LED indication of any operation.
RS-232 interface.
Data maintained without batteries.
Programming with DATALINK software.

Included Accessories

Set of two alligator clips, KITXL423C.
RS-232 serial cable, type C2004.
Adhesive Velcro for fixing.
Carrying bag, type BORSA2000.
User’s manual.

Specifications (accuracy stated at 23°C ±5°C ±(% of rdg + number of digits), < 60% R.H.)
Measurement Range	0 Volts to 600 Volts
Resolution	0.1 Volt
Accuracy	±(1.0% of reading + 2 digits)
Working Frequency	50/60Hz ±6%
Type of Measurement	True Rms
Bandwidth	3200Hz
Maximum Crest Factor	3
Note: meter consider null readings < 2 volts

General Specifications
Sampling Rate	64 point, 20ms for each sampling period
Sampling Period	1 sec, 6 sec, 30 sec, 1 min, 5 min
Memory Capacity	1 Mbyte Life in days (depending on batteries life): 5 days/1 sec; 34 days/6 sec; 170 days/30 sec; 364 days/1 min; 1820 days/ 5 min
Computer Interface	RS-232
Operating Temperature/Humidity	-20°C to 60°C; 0 to 100% R.H. (RS-232 connector closed)
Storage Temperature	-20°C to 60°C; 0 to 100% R.H. (RS-232 connector closed)
Insulation	class 2 (double insulation)
Protection Degree	IP65 (RS-232 connector closed)
Maximum Altitude	2000 meters

Reference Standards	LVD: IEC/EN 61010-1 CAT III 1000V (to ground), CAT IV 600V (to ground)
Reference Standards	EMC: IEC/EN 61326 (1997) +A1 (1998) +A2 (2001)

Power Supply	2 x 1.5 volt type ‘AA’ alkaline batteries type LR6, AM3, MN1500
Battery Life	6 months
Dimensions	120mm (L) x 80mm (W) x 43mm (D)
Test Lead Length	2.6 meters
Weight	500g (with internal batteries)

The post HT Italia XL423 True-Rms AC Single-Phase Voltage Logger appeared first on rapid-tech.