Accessories Supplied with HT65

•  Pair of test leads
•  Adapter + K-type wire probe
• Batteries
•  ISO9000 calibration certificate
•  Carrying bag
•  User manual

HT Instruments HT65 TRMS Digital Multimeter Approvals

The post HT Instruments HT65 TRMS Digital Multimeter for DC voltage up to 1500V appeared first on rapid-tech.

HT Instruments NEPTUNE Key Features:

• it can quickly measure insulation up to 1000V, just like top-of-the-range testers.
• 50,100,250,500,1000VDC Insulation test voltages.
• it measures continuity of protective conductors with 200mA to solve the most common problems related to masses.
• measure Inrush currents, Harmonics and THD%, just like top-of-the-range power quality analyzers.
• with a wide range of external clamp transducers it can measure AC TRMS, DC, AC+DC current and Inrush current, starting from 1mA up to 3000A.
• compare each measurement with the limits prescribed by the Guidelines and I provide a clear result OK or NOT OK
• it’s a multimeter with functions only available if using top-of-the-range instruments.
• CAT IV 600V, CAT III 1000V Safety Rating
• Similar to the Fluke 1587 & Fluke 1577
• ISO 9000 CALIBRATION CERTIFICATE INCLUDED

HT Instruments NEPTUNE  Included Accessories:

• 4324-2 Pair of Red/Black banana connectors with 2/4mm tip
• YAAMK0001HT0 Pair of Red/Black alligator clips
• YABAT0001HT0 Alkaline battery type AAA IEC LR03 1.5V, 4 pieces
• YABRS0002HT0 Carrying bag
• YAMUM0068HT0 User manual on CD-ROM
• YAMUM0067HT0 Quick user guide
• Calibration certificate ISO9000

Optional Accessories:

• F3000U Flexible clamp with full scale 30/300/3000A AC and banana connectors
• HT96U* Standard clamp with full scale 1/100/1000A AC and Hypertac connector
• HT97U* Standard clamp with full scale 10/100/1000A AC and Hypertac connector
• HT98U* Standard clamp with full scale 1000A DC and Hypertac connector
• HT4006 Standard clamp with full scale 40/400A AC/DC and banana connectors
• NOCANBA Adapter for clamp connection with Hypertac connector
• 5004-IECR Red alligator clip
• 5004-IECN Black alligator clip
• C2065 3-wire cable Red, Black and Green with Schuko plug

The post HT Instruments NEPTUNE Multimeter/Insulation Tester appeared first on rapid-tech.

HT Instruments MERCURY Multimeter Function:

• DC/ AC / AC+DC TRMS voltage
• DC / AC / AC+DC TRMS current
• DC / AC / AC+DC TRMS current with clamp transducer
• Resistance and Continuity test
• Diode test
• Capacitance
• Frequency
• Duty Cycle
• Temperature with K-type probe
• Data Logger function and display of graphs of measured data
• Storage of BMP images on external micro SD card
• CAT IV 600V – CAT III 1000V Safety Rating

HT Instruments MERCURY Thermal Imaging Camera Function:

• Infrared temperature measurement ranging from -20°C to 260°C
• 3 measuring cursors (central steady + hot spot + cold spot)
• Emissivity of materials which can be selected between 0.01 and 1.00
• Image frequency: 50Hz
• 5 selectable color palettes
• Automatic detection of hot/cold spots of the image
• Storage of BMP images on external micro SD card
• IR sensor resolution: 80x80pxl
• Bluetooth connection to mobile devices through the APP HTMercury
• Built-in laser pointer and illuminator

Each of the above functions can be selected by means of the appropriate switch. The MERCURY is also equipped with function keys, analogue bargraph and LCD TFT high-contrast color display. The Mercury is also equipped with an Auto Power OFF function which automatically switches off the instrument after a certain (programmable) idling time.

Included Accessories:

• Pair of leads (red & black) with 2/4mm tip (Code 4413-2)
• Adapter & K-type thermocouple wire probe
• Flexible clamp transducer AC 30/300/3000A (Code F3000U)
• Li-ION rechargeable battery, 2 pieces (Code BATMCY)
• Multiplug Universal power supply + recharging base (Code A0MCY)
• Alkaline battery type AAA LR03, 2 pieces
• Micro SD card, 8GB
• Carrying bag (Code B0MCY)
• ISO9000 calibration certificate
• User manuals

Why True RMS?

Measuring instruments for AC are divided into two types: 

• AVERAGE-VALUE meters: instruments measuring the value of the sole wave at fundamental frequency (50 or 60 Hz). 
• TRMS (True Root Mean Square) VALUE meters

True RMS instruments measuring the TRMS value of the quantity being tested. With a perfectly sinusoidal wave, the two families of instruments provide identical results. With distorted waves, instead, the readings shall differ.

Average-value meters provide the RMS value of the sole fundamental wave; TRMS meters, instead, provide the RMS value of the whole wave, including harmonics (within the instruments bandwidth).

Therefore, by measuring the same quantity with instruments from both types, the values obtained are identical only if the wave is perfectly sinusoidal. In case it is distorted, TRMS meters shall provide higher values than the values read by average-value meters.

The post HT Instruments Mercury Infrared Digital Multimeter appeared first on rapid-tech.

The HT Instruments FLASHMETER is a compact DMM capable of carrying out TRMS voltage measurements up to 600V as well as resistance measurements automatically under autorange, just connecting input terminals.

It was designed in compliance with safety standards IEC/EN61010-1 with double insulation protection under CAT IV 600V. The HT Instruments FLASHMETER has an inbuilt white light torch, a non-contact probe to detect AC voltage and is water resistant according to IP67.

HT Instuments FlashMeter Specifications:

The Ht Instruments FlashMeter conforms to the following standards:

The post HT Instruments FLASHMETER TRMS Digital Multimeter appeared first on rapid-tech.

The new series of HT professional multimeters is the result of an important research conducted at the most demanding users of this kind of equipment, namely laboratories where the choice of a measuring instrument is subject to strict tests concerning precision, reliability and safety of measurements even in extreme conditions. Therefore, a complete range multimeters, all able to measure in TRMS, all within CAT IV 600V, autorange function available on all models, with backlight display. The design is extremely modern and attractive, but also ergonomic, to ensure maximum ease of use. Display with high resolution, even in color version, for the premium model HT64.

HT Italia HT60 functions can be selected using the 7-position rotary switch, including an OFF position. The instrument is also provided with a HOLD function key to enable freezing the measured value on the display and to activate the display’s backlight, an Hz% key to select frequency and duty cycle tests, a REL key to carry out relative measurements and a MODE key to select resistance measurement, continuity test, diode test and capacity test. The selected quantity appears on the LCD display with the indication of the measuring unit and of the enabled functions. The instrument is also equipped with an Auto Power OFF device which automatically switches it off approx. 30 minutes after the last time the instrument was used. It is similar to the Fluke 110 and Fluke 114.

MEASURING AVERAGE VALUES ANDTRMS VALUES Measuring instruments of alternating quantities are divided into two big families:  AVERAGE-VALUE meters: instruments measuring the value of the sole wave at fundamental frequency (50 or 60 Hz).  TRMS (True Root Mean Square) VALUE meters: instruments measuring the TRMS value of the quantity being tested. With a perfectly sinusoidal wave, the two families of instruments provide identical results. With distorted waves, instead, the readings shall differ. Average-value meters provide the RMS value of the sole fundamental wave; TRSM meters, instead, provide the RMS value of the whole wave, including harmonics (within the instruments bandwidth). Therefore, by measuring the same quantity with instruments from both families, the values obtained are identical only if the wave is perfectly sinusoidal. In case it is distorted, TRMS meters shall provide higher values than the values read by average-value meters

HT Italia HT60 TRMS Digital Multimeter with Temperature Functions

The post HT Italia HT60 TRMS Digital Multimeter with Temperature appeared first on rapid-tech.

Autorange measurements with automatic AC/DC detection
LoZ low impedance voltage input to eliminate ghost voltage readings (caused by the capacitive coupling among active conductors close each other)
One-lead phase sequence detection

JUPITER is provided with ISO9000 calibration certificate as standard.

HT Instruments JUPITER Multifunction Multimeter Features:

• Autorange measurements with automatic AC/DC detection.
• DC, AC TRMS, AC+DC TRMS voltage up to 690V.
• Tripping time of RCDs type A and AC up to 300mA*.
• Tripping current of RCDs type AC up to 30mA. ›
• Non-trip earth ground resistance. ›
• Line-to-Neutral, Line-to-Line and Line-to-Ground impedance (resolution 0.1Ohm) with prospective short-circuit/fault current calculation.
• Current up to 3000A by means of clamp-on or flexible external transducer.
• Dynamic inrush current of motors and loads through the DIRC function allowing time base selection.
• Leakage current by means of the clamp-on transducer HT96U.
• Voltage and current harmonics with THD% calculation and function to the 25th Harmonic showing highest harmonic values first.
• One-lead phase sequence detection.
• Low impedance voltage input to eliminate ghost voltage readings.
• DC, AC TRMS, AC+DC TRMS current by means of external transducer.
• Frequency of voltage and/or current.
• Resistance and continuity with buzzer.
• MIN/MAX/PEAK/HOLD functions.
• 6000 count Display

HT Instruments JUPITER Multifunction Multimeter Functions:

• C2033AU Three wire cable Red, Black, Green with Australian plug
• 4324-2 Pair of test tips Red/Black 2/4mm straight banana
• YABAT0001HT0 Alkaline battery 1.5V, type AAA, IEC LR03, 4 pcs
• YABRS0002HT0 Carrying bag
• YAMUM0066HT0 User manual on CD-ROM
• YAMUM0065HT0 Quick reference guide
• Calibration certificate ISO9000.

 

HT Instruments JUPITER Optional Accessories:

• F3000U AC flexible clamp with 30/300/3000A full scales
• HT96U* AC current clamp with 1/100/1000A full scales
• HT97U* AC current clamp with 10/100/1000A AC full scales
• HT98U* DC current clamp with 1000A full scale
• HT4006 AC/DC current clamp with 40/400A full scales
• NOCANBA Hypertac-to-banana adapter* Adapter NOCANBA required.

The post HT Instruments JUPITER Multifunction Multimeter appeared first on rapid-tech.

The HT Instruments IRONMETER is the perfect construction site multimeter with a sturdy case able to withstand shocks of all kinds, always ready to get up after a fall, (even from 3 meters height) and continue to operate with the same accuracy and reliability. It has all the features required for typical daily usage an has an inbuilt LED flashlight to light up areas with poor lighting.

The HT Instruments  IRONMETER is a professional, autoranging TRMS multimeter with an impact resistant double molded housing. The HT Instruments  IRONMETER provides all the important functions of a True-RMS-Multimeter in a single compact handheld unit. The case has been designed specifically to make the multimeter more robust than ever before and making it as indestructible as possible. The measurement functions allow the use in almost all electrical areas. The HT IRONMETER is equipped with two high-power LEDs which guarantee a lighting range of up to 30 m. 

HT IRONMETER Functions
* DC voltage
* AC TRMS voltage
* DC current (up to 10 A (20 A max. 30 s) 
* AC TRMS current (up to 10 A (20 A max. 30 s)
* Resistance and Continuity Test & Buzzer
* Frequency
* Duty Cycle
* Diode Test
* Capacity
* Data HOLD, MAX / MIN
* Magnet for mounting on metal surfaces & Belt clip
* Light beam adjustable for torch lamp
* Dimensions: 120 x 65 x 45mm
* Weight: 200gm

The post HT Instruments IRONMETER Rugged True RMS Multimeter appeared first on rapid-tech.

The new HT ITALIA HT64 professional multimeter is the result of an in depth research conducted with the most demanding users of this kind of equipment, namely laboratories, where the choice of a measuring instrument is subject to strict tests concerning precision, reliability and safety of measurements even in extreme conditions. Therefore the HT 60 series is a complete range multimeters, all able to measure in TRMS, all with CAT IV 600V Safety Rating, autorange function available on all models, with backlight display.

HT ITALIA HT64 Measurement Features:

• DC voltage
• AC, AC+DC TRMS Voltage
• DC current
• 4-20mA% display
• AC, AC+DC TRMS current
• Resistance and Continuity test
• Diode test
• Capacitance
• Frequency
• Duty Cycle
• Temperature with K-type probe
• Data Logger function and display of graphs of measured data

These features that make the HT Italia HT64 unique and invaluable.

Similar to the Fluke 287

HT ITALIA HT64 Specifications:

1. ELECTRICAL SPECIFICATIONS

Accuracy calculated as ±[%reading + (num dgt * resolution)] at 18°C ¸ 28°C, <75%HR

DC VOLTAGE

AC TRMS VOLTAGE

(*) Accuracy specified from 5% to 100% of measurement range, Input impedance: >9MΩ,

Response time PEAK function: >1ms, Accuracy PEAK function: ±10%rdg

AC+DC TRMS VOLTAGE

DC CURRENT

AC, AC+DC TRMS CURRENT

(*)Accuracy specified from 5% to 100% of measurement range

Response time PEAK function: >1ms, Accuracy PEAK function: ±10%rdg

AC+DC TRMS Current: accuracy (50Hz¸1kHz): ±(3.0%rdg + 20dgt)

4-20mA% READINGS

DIODE TEST

RESISTANCE AND CONTINUITY TEST

FREQUENCY (Electronic circuits)

FREQUENCY (Electrical circuits)

DUTY CYCLE

Pulse frequency range: 40Hz ¸ 10kHz, Pulse width: ±5V (100ms ¸ 100ms)

CAPACITANCE

TEMPERATURE WITH TYPE K PROBE

(*)Accuracy referred to instrument without probe

GENERAL SPECIFICATIONS

Display:

• TFT LCD, colours, 4½ dgt, 6000 counts, decimal point and bargraph
• Automatic polarity indication
• Backlight
• “OL” over range indication
• Response time: 3/s

The post HT ITALIA HT64 TRMS/AC+DC Digital Multimeter with colour LCD display appeared first on rapid-tech.

HT ITALIA HT701 TRMS Multimeter + Insulation Meter

HT ITALIA HT701 model is a TRMS professional multimeter designed to perform basically AC/DC voltage measurements up to 1000V, AC/DC current measurement up to 400mA more than resistance, continuity test, diode test, frequency, capacitance, and temperature with type K probes as sub-features.

The post HT ITALIA HT701 TRMS multimeter + Insulation Meter up to 1kVDC appeared first on rapid-tech.

Voltage measurements AC/DC and current measurements AC/DC up to 10A maximum.
Plus resistance, continuity and diode tests, along with capacitance, frequency and duty cycle as sub-features.

HT ITALIA HT326 Functions:

• HOLD function, relative function and manual range selection
• In compliance to EN 61010-1 safety standard with double insulation protection
• Large LCD display with backlight
• Each measurement function can be selected with a rotating selector dial with 10 positions
• AutoPowerOff function is integrated to preserve the battery after 15 minutes of inactivity

The post HT ITALIA HT326 CAT IV Digital Multimeter with Capacitance and Duty Cycle appeared first on rapid-tech.