Measurement functions

• Universal 4mm sockets for connection to a 1- or 3-phase installation tester using test leads (banana plugs)
• Separate phase display with three LEDs for easy voltage checking
• Proximity Pilot (PP) rotary switch for simulating different current carrying capacities of charging cables
• Control Pilot (CP) rotary switch for simulating the electrical vehicle status A, B, C D
• Rotary switch error to simulate a short circuit between CP and PE (state E = error)
• Simulation of PE fault (ground fault)
• Connection for the CP signal output to check communication between the adapter (= simulated electric vehicle) and the charging station
• Type 2 plug for connection to the charging station even with a permanently connected charging cable
• Vehicle simulation (CP): The various vehicle states A to D can be simulated using a rotary switch (according to IEC 61851)
• Cable simulation (PP): The various codings for charging cables with 13, 20, 32 and 63 A as well as “no cable connected” can be simulated using a rotary switch
• Error simulation: Simulation of a short circuit between CP and PE using a rotary switch (state E = error)
• Display of phase voltages via LEDs
• Testing of e-charging stations even with a permanent
• connected charging cable
• For vehicle simulation (CP):

According to IEC 61851, the states A, B, C, D and E can be simulated. The various vehicle states are set using the rotary switch.

The post HTI EV-TEST100 EVSE Adapter for Electric Vehicle Charger Testing appeared first on rapid-tech.

Multifunction Tester for safety of machinery IEC/EN60204-1:2016 and low voltage switchgears and controlgears IEC/EN61439-1-2:2011

IEC/EN60204-1:2016 Measuments:

Power Frequency Dielectric withstand voltage with test voltage of 1000VAC

Testing protection against indirect contact:

• Continuity of protective conductors with test current 200mA
• Automatic disconnection of the supply (RCD, MCB, Fuse)​
• RCD tripping (RCD AC, A, B) up to 1A on TT Systems
• Magneto-thermal protections (MCB curve verificaiton on B, C, D, K) and fuses (gG, aM) on TN Systems

​Insulation resistance measurement with test voltage of 500VDC

Discharging of residual voltage V<60V in 5sec/1sec

IEC/EN61439-1-2:2011 Measurements:

Clearances and Creepage distances:

• Dielectric withstand voltage with test voltage of up to 3400/5100VAC

Continuity of earth system and protective conductors ≥10A

Power Frequency Dielectric withstand voltage with test voltage of 1800VAC

Alternative power-frequency voltage test up to 5100VAC

Test on enclosures of insulating material:

• ​Dielectric Withstand voltage with test voltage up to 2835V

Discharging of residual voltage V<60V in 5sec/1sec

FULLTEST3 is designed to satisfy the requirements of the IEC/EN60204-1:2006 guideline (electrical equipment of industrial machines) and for the new series of prescriptions relative to the IEC/EN61439-1 guideline (Switchgear panels). This last guideline require, among other tests, the Dielectric tests with a test voltage up to 5100V!

FULLTEST3 Features:

• Continuity of protection conductors with 200mA
• Continuity of protection conductors with I>10A, V<12V AC
• Continuity of protection conductors with I>25A, V<12V AC
• Insulation Resistance with 100,250,500,1000VDC test voltage
• Withstanding test with test voltage programmable from 250V to 5100V AC
• Discharging time test on internal capacitance and on power supply plug
• Leakage/absorbed and power on the test socket
• Leakage current with external clamp (HT96U optional accessories)
• Test on RCDs type A, AC, B General, Selective, Delayed up to 1000mA
• Line/Loop impedance and Ipsc calculation
• Line/Loop impedance with high resolution (with IMP57 optional accessories)
• Test on MCB protection with curve B, C, D, K and Fuse type gG and aM
• Selection of length, cable type, insulation of cable, tripping time of protection device
• Global earth resistance without RCD tripping
• Phase sequence indication
• TFT display with touch-screen
• Programmable timer on tests
• Programmable thresholds on measurement
• Internal memory
• USB interface for PC connection
• USB interface for keyboard, printer and barcode reader connection

Test to Guidelines:

Standard Accessories:

• Australian Power cord
• Test cable red, 3 metre, 2 pcs
• Test cable blue, 3 metre
• Test cable green, 3 metre
• C2033X : Cable 3 wires with Shuko plug
• Cable with 5kV safety, 2 pcs
• Test lead CAT III, 3 pcs
• Test lead CAT II, 3 pcs
• Alligator clip, 3pcs
• TOPVIEW2007 : Windows software + USB cable C2007
• Carry bag for accessories
• ISO9000 calibration certificate

Optional Accessories:

• IMP57 : Accessory for high resolution Loop/Line Impedance
• HT96U : Rigid clamp 1-100-1000A AC, diameter 54mm

The post HT Instruments FULLTEST3 Professional Multifunction Safety Tester appeared first on rapid-tech.

HT Instruments NEPTUNE Key Features:

• it can quickly measure insulation up to 1000V, just like top-of-the-range testers.
• 50,100,250,500,1000VDC Insulation test voltages.
• it measures continuity of protective conductors with 200mA to solve the most common problems related to masses.
• measure Inrush currents, Harmonics and THD%, just like top-of-the-range power quality analyzers.
• with a wide range of external clamp transducers it can measure AC TRMS, DC, AC+DC current and Inrush current, starting from 1mA up to 3000A.
• compare each measurement with the limits prescribed by the Guidelines and I provide a clear result OK or NOT OK
• it’s a multimeter with functions only available if using top-of-the-range instruments.
• CAT IV 600V, CAT III 1000V Safety Rating
• Similar to the Fluke 1587 & Fluke 1577
• ISO 9000 CALIBRATION CERTIFICATE INCLUDED

HT Instruments NEPTUNE  Included Accessories:

• 4324-2 Pair of Red/Black banana connectors with 2/4mm tip
• YAAMK0001HT0 Pair of Red/Black alligator clips
• YABAT0001HT0 Alkaline battery type AAA IEC LR03 1.5V, 4 pieces
• YABRS0002HT0 Carrying bag
• YAMUM0068HT0 User manual on CD-ROM
• YAMUM0067HT0 Quick user guide
• Calibration certificate ISO9000

Optional Accessories:

• F3000U Flexible clamp with full scale 30/300/3000A AC and banana connectors
• HT96U* Standard clamp with full scale 1/100/1000A AC and Hypertac connector
• HT97U* Standard clamp with full scale 10/100/1000A AC and Hypertac connector
• HT98U* Standard clamp with full scale 1000A DC and Hypertac connector
• HT4006 Standard clamp with full scale 40/400A AC/DC and banana connectors
• NOCANBA Adapter for clamp connection with Hypertac connector
• 5004-IECR Red alligator clip
• 5004-IECN Black alligator clip
• C2065 3-wire cable Red, Black and Green with Schuko plug

The post HT Instruments NEPTUNE Multimeter/Insulation Tester appeared first on rapid-tech.

The GSC60 MEASURES:

›    Earth Resistance with 2- or 3-pole volt-ampere method in TT, TN and IT systems, non-trip earth loop impedance measurement, stackless earth ground resistance measurement  with T2100 (optional).

›    Soil Resistivity with 4 pole Wenner method.

›    RCD Testing type A, AC, B with test current up to 10A.**

›    Insulation Resistance measurement with test voltage up to 1000V.

›    Continuity measurement of protective conductors with test current up to 200mA.

›    Advanced Loop Testing of MCBs, fuses and cable sizing.

›    Measurement of phase sequence (SEQ).

›    Measurement and recording of environment parameters and leakage currents through external probes.

HT INSTRUMENTS GSC60 for the Analysis of Power Quality and Energy Consumption.

›    9 types of electrical systems: 1Φ-2wires, 1Φ-split phase, 3Φ-3 wires, 3Φ-Aron, 3Φ-Open Δ, 3Φ-Open Y, 3Φ-2 el. 1/2, 3Φ-4 wires Y, 3Φ-High Leg.

›    632 parameters can be recorded for over two months.

›    Real Time. Real-time display of all waveforms, harmonics, vector diagrams as well as summary function on phases for a quick reading of the most important parameters.

›    Voltage Anomalies. Detection of voltage anomalies with a resolution of 20ms.

›    Energy Saving. One click allows you to check all the electrical absorption of all the equipment connected to the main power supply and save on energy costs.

Live. Real Time Analysis.

Wi-Fi connection allows you to display wave forms, vector diagrams, harmonics and all electrical parameters for each phase on your tablet/smartphone/PC

GSC60 helps to dispel the myth that recording analysis is complex. App HTanalysis makes it simple and clear. Using ZOOM Functions you can display all the recorded quantities. JUMP Function displays harmonics in any recording step just by clicking on the quantity.

HT INSTRUMENTS GSC60 Functions:

The post HT INSTRUMENTS GSC60 Multifunction Electrical Analyzer appeared first on rapid-tech.

Designed according to the requirements of field professionals, HT Italia HT9 is must-have troubleshooting tool.

Two pole voltage meter with Lamp Test. With built-in gas-filled lamp tester and non-contact phase sequence/conformity tester

Digital two pole voltage tester HT Italia HT9 provides daily use features. In addition to DC/AC voltage measurement and continuity test, HT9 also offers gas-filled lamp test and phase sequence/conformity detection features. To overcome difficult pinpointing of the right cable within a frame on a switchboard under poor light conditions, a built-in white LED flashlight makes testing possible and easy even in dark environments. The slim and ergonomic design of HT9 is highly appreciated by contracting electricians, field professionals, troubleshooters as well as any vkind of user. Designed according to the requirements of field professionals, HT9 is must-have troubleshooting tool.

Figure 2 – HT Italia HT9 LED and Display Description
1.	Voltage indication leds
2.	Buzzer hole for acoustic signal
3.	Indication led Lamp test
4.	Indication led Phase sequence
5.	Indication led Phase detection / Dangerous voltage
6.	Indication led Continuity test
7.	Indication led 12V and positive or negative polarity
8.	LCD display with voltage, polarity and flat battery indic

HT Italia HT9 Specifications:

The post HT Italia HT9 Two-pole CAT IV Voltage Tester with Lamp Test appeared first on rapid-tech.

HT ITALIA HT70 Description:

1. Voltage Detection Sensor
2. Reference Mark CAT-IV Measurement
3. Hand Safety Protection
4. “ON” Switch and white LED indication
5. Pocket “Pen” Clip
6. RED/GREEN Indicator
7. Pressure Point to remove Battery Cover
8. Battery Cover Slide.

Voltage detection test:

1. Turn on the meter by pressing ON/OFF key for at least 1s. Waiting for the standby mode when the green LED is blinking

2. Position the sensor close to or in contact with the point under test for a time <5s, then verify that the red LED is on and buzzer sounds continuously as evidence of voltage detection. Do not perform test with the operator’s hand beyond the hand safety protection and position not insulated wires beyond the CAT IV reference mark (see part 2 of the picture above)

3. Press ON/OFF key for at least 3s to turn off the meter

HT Italia HT70 Specifications:

The post HT Italia HT70 Voltage Stick with Phase Sequence Tester appeared first on rapid-tech.

HT ITALIA HT20S Description:

1. Voltage Detection Sensor
2. Reference Mark CAT-IV Measurement
3. Hand Safety Protection
4. “ON” Switch and white LED indication
5. Pocket “Pen” Clip
6. White LED Torch
7. Pressure Point to remove Battery Cover
8. Battery Cover Slide.

HT ITALIA HT20S Operating Instructions:

1. Switch on the instrument by pressing key
2. Perform an initial test with meter on an energized circuit. Replace internal batteries if the red LED do not turn on and/or the buzzer do not sound
3. Position the sensor close to or in contact with the point under test then verify that the red LED is on and buzzer sounds continuously as evidence of voltage detection. Do not perform test with the hand beyond the hand safety protection and do not allow insulated wires beyond the CAT IV reference mark (see part 2 of above picture)
4. If needed press key to turn on the white torch
5. The instrument switch off automatically after 5 minutes of idleness

HT ITALIA HT20S Technical specifications:

• Voltage reference range: 100-1000V AC to ground
• Frequency reference range: 50/60Hz
• Meter indications: visible LED and acoustic buzzer
• Safety: IEC/EN61010-1
• Category of measurement: CAT IV 1000V
• Pollution degree: 2
• Batteries: 2 x 1.5V alkaline type AAA IEC LR03
• Working temperature: -10°C to 50°C
• Working humidity: -10 to 40°C;<75%HR; 40-50°C <45%HR
• Dimensions (L-W-H): 160 x 26 x 20mm
• Weight (included batteries): 48g

The post HT ITALIA HT20S Phase Detector with Torch appeared first on rapid-tech.