When Your Standard Multimeter Isn’t Enough

Every electrical contractor and maintenance engineer has been there: an intermittent fault that defies diagnosis with a handheld multimeter, a motor inrush current that trips protection for no apparent reason, or a voltage sag on a commercial power supply that only appears during peak load periods. These aren’t problems you can solve with spot readings — you need to capture what’s actually happening on the waveform over time.

The HIOKI MR8880 Memory HiCorder is purpose-built for exactly these situations. It’s a portable, field-ready data acquisition recorder designed to simultaneously monitor multiple high-voltage channels, capture transient events with precise triggering, and deliver the kind of waveform data that turns guesswork into documented evidence.

Whether you’re investigating power quality issues in a commercial switchboard, verifying motor start-up behaviour for a commissioning report, or monitoring an uninterruptible power supply (UPS) for voltage drop events, the MR8880 puts laboratory-grade recording capability into a package that fits in your tool bag.

Direct 600 V Input — Leave the Differential Probes Behind

One of the most significant practical advantages of the MR8880 is its ability to accept direct voltage input up to 600 V AC/DC at CAT III safety ratings, with CAT IV coverage at 300 V AC/DC. For Australian electricians and maintenance professionals working on 415 V three-phase commercial and industrial supplies, this means you can connect directly to the power line without needing a separate differential probe.

That’s not just a convenience — it’s a genuine time-saver on site. Fewer accessories means faster setup, less equipment to carry, and reduced risk of connection errors. The four completely isolated analog channels let you measure all three phases of a power system simultaneously, with the fourth channel free for a neutral reference, control signal, or current waveform via an optional clamp sensor.

Rugged Enough for Australian Conditions

Australian job sites test equipment in ways that many manufacturers don’t design for. Summer temperatures inside a metal switchboard can easily exceed 40°C, while winter mornings in a Tasmanian substation might start below freezing. The MR8880 is rated for an operating temperature range of -10°C to 50°C, which covers the vast majority of field conditions you’ll encounter across the country.

The instrument also arrives with standard side protectors designed to absorb impacts and vibrations — it meets JIS automotive vibration standards, which speaks to its durability in transit and on active work sites. At just 1.66 kg with the battery pack installed, it’s light enough for extended carry without fatigue, yet substantial enough to feel like a professional-grade tool.

High-Speed Capture Meets Long-Term Monitoring

The MR8880 operates in two distinct measurement modes, giving you flexibility to match the recording approach to your investigation:

High-Speed Function: When you need to capture fast transient events — motor inrush currents, relay switching transients, or voltage spikes — the high-speed mode delivers sampling rates up to 1 MS/s (1 microsecond per sample) across all four channels simultaneously. The time axis ranges from 100 µs/div to 100 ms/div across 10 selectable ranges, with a sampling period of 1/100th of the selected range. This resolution ensures you won’t miss the critical details hidden within rapid electrical events.

Real-Time Function: For longer-duration monitoring tasks — tracking voltage stability over hours, logging RMS fluctuations during equipment commissioning, or capturing intermittent faults that occur unpredictably — the real-time recording function supports intervals from 100 µs to 1 minute across 19 selectable options. Data is saved continuously with simultaneous sampling across all channels, and you can write directly to external storage media (CF card or USB memory) at rates up to 10 kS/s for extended recording sessions.

With 14-bit resolution and 1 M-word per channel memory depth (1 word = 2 bytes), the MR8880 captures waveform detail with enough precision to reveal subtle anomalies that lower-resolution instruments would miss entirely.

Intelligent Triggering That Catches What Matters

The real power of a memory recorder lies in its triggering capability. The MR8880 offers advanced trigger settings that go far beyond simple level crossing. You can configure triggers based on voltage thresholds, RMS values, peak waveform levels, or logic signal states — and the pre-trigger function captures data from before the trigger event, so you get the full context of what caused the anomaly, not just what happened after.

This is particularly valuable for power quality investigations where you need to document the sequence of events leading up to a voltage drop, sag, or transient. The built-in cursor functions then let you identify numerical values of peak currents, timing intervals, and waveform characteristics directly on the 5.7-inch colour LCD display — no PC required for initial analysis.

PRESETS Configuration — Because Time on Site Is Money

HIOKI’s patented PRESETS function addresses a common frustration with advanced test equipment: the setup complexity. Rather than navigating through multiple menu layers to configure measurement ranges, trigger levels, time bases, and recording modes manually, PRESETS lets you select your measurement application — “Measure a commercial power supply,” “Monitor a power source for a voltage drop,” and so on — and guides you through the appropriate settings with on-screen instructions.

For a busy sparkie who doesn’t use a memory recorder every day, this dramatically reduces the risk of misconfiguration and gets you capturing useful data faster. It’s the difference between spending fifteen minutes wrestling with settings and being up and recording within a couple of minutes.

Eight Logic Channels for Control Signal Analysis

Beyond the four analog channels, the MR8880 includes eight built-in logic channels as standard. When paired with an optional logic probe (such as the MR9321-01 with four isolated channels), you can simultaneously monitor control signals, PLC outputs, relay states, and other digital events alongside your voltage and current waveforms.

This is essential for troubleshooting automated systems where you need to correlate a physical event (motor start, breaker trip, valve operation) with the control signal timing. The trigger system supports AND/OR logic conditions across both analog and logic channels, enabling precise event-based capture of complex sequences.

Flexible Power Options for Any Situation

Field accessibility is central to the MR8880’s design. It supports four different power supply options to suit virtually any measurement scenario:

The included AC adapter (Z1002) operates on 100–240 V AC globally, drawing 45 VA during real-time recording. The optional rechargeable NiMH battery pack (Z1000) provides approximately three hours of continuous use with the backlight on and recharges in about three hours via the AC adapter. For quick deployments, eight AA alkaline batteries deliver roughly 40 minutes of operation. There’s also a DC power input (10–28 V DC) for vehicle-based or solar-powered applications.

When the AC adapter and battery pack are used together, the adapter takes priority while simultaneously charging the battery — a thoughtful design touch that ensures uninterrupted recording during extended monitoring sessions.

Data Management and PC Connectivity

Measurement data can be saved to CF cards (up to 2 GB) or USB memory sticks directly from the instrument. Real-time data can be written continuously to external media, and you can swap storage devices without interrupting the recording — a critical feature for multi-day monitoring tasks.

The USB 2.0 mini-B port enables direct PC connection for file transfer and remote instrument control. The optional Wave Processor 9335 software provides comprehensive waveform display, analysis, and format conversion capabilities on your computer, making it straightforward to generate professional reports and documentation for compliance records.

An optional A6-size thermal printer unit (MR9000) attaches directly to the MR8880 for printing waveform records on site — useful for immediate documentation during commissioning or fault investigation.

Extensive Current Measurement Ecosystem

While the MR8880’s built-in channels handle voltage measurement directly, HIOKI offers a comprehensive range of compatible current sensors covering everything from milliamp leakage currents to 2,000 A load currents. High-precision AC/DC sensors with frequency response up to 2 MHz are available for motor drive and inverter analysis, while simpler clamp-on probes suit general load current monitoring.

This modular approach means you can configure the MR8880 precisely for your application — whether that’s a simple three-phase voltage and current power quality study, a detailed motor start-up analysis with high-bandwidth current capture, or a combined analog and logic signal investigation on an automated production line.

TECHNICAL SPECIFICATIONS TABLE

The post HIOKI MR8880-20 Memory HiCorder | 4-Ch 600V Portable DAQ Recorder appeared first on rapid-tech.

If you’ve ever felt that moment of tension when connecting test leads to live terminals, you know the drill. One slip, one accidental contact between probes, and you’re dealing with an arc flash, a blown circuit, or worse. For electrical contractors, facility managers, and energy auditors working on energized systems, this risk comes with the territory—until now.

The HIOKI PW3365 Clamp-On Power Logger fundamentally changes how Australian professionals approach power measurement. As the world’s first power logger with completely non-metallic contact voltage sensors, this instrument eliminates the physical risk that’s plagued power testing since day one. No exposed metal contacts. No direct terminal connections. No accidental short circuits.

Instead of fumbling with traditional voltage probes that need precise terminal placement, the PW3365 uses innovative fully-insulated voltage clips that attach anywhere along insulated cables or busbars. Clip around the wire jacket, not onto exposed metal—it’s that straightforward. This breakthrough design means you can measure 3-phase power systems while circuits remain energized and covered, without ever removing terminal guards or exposing live parts.

Real-World Problem: Why Traditional Power Testing Creates Dangerous Situations

Every sparky and facility tech knows the scenario: you need to log power consumption on a 3-phase distribution board to identify energy waste or verify equipment performance. Traditional power analyzers require you to:

1. Isolate the circuit or work live with exposed terminals
2. Carefully position voltage probes on metal contact points
3. Maintain safe clearances while managing multiple leads
4. Risk short circuits if probes slip or make unintended contact
5. Navigate around terminal covers that block access

This process isn’t just time-consuming—it’s genuinely hazardous. Australian electrical safety regulations (AS/NZS 3000:2018) emphasize risk elimination wherever possible. Working on live circuits with traditional test equipment places technicians in harm’s way for routine measurements. Facility managers conducting energy audits face tough decisions: shut down critical equipment for testing, or accept the risks of live testing.

The PW3365 solves this by making voltage measurement genuinely non-contact. The fully-covered PW9020 voltage sensors clip around insulated cables without any metal-to-metal connection. Short circuits become physically impossible because there’s no exposed metal on the voltage sensing clips.

How the PW3365’s Non-Contact Technology Works in Practice

Traditional Power Measurement:

• Voltage test leads with metal tips
• Must connect to bare metal terminals
• Risk of accidental shorts between phases or phase-to-ground
• Requires removing protective terminal covers
• Impossible to test through cable insulation

HIOKI PW3365 Approach:

• Fully-insulated voltage clips with zero exposed metal
• Clip directly around insulated cables or busbars
• Physically impossible to create short circuits
• Works through cable jackets—no need to access terminals
• Install sensors while equipment remains fully protected

This isn’t just a safety improvement—it’s a workflow transformation. Energy consultants conducting building audits can quickly clip sensors onto distribution cables without coordinating downtime. Industrial maintenance teams monitoring motor loads don’t need isolation permits. Solar installers verifying inverter output can test while systems remain energized.

Comprehensive 3-Phase Power Monitoring Without the Complexity

Beyond the safety innovation, the PW3365 delivers the measurement capabilities Australian electrical professionals actually need for real-world applications:

Complete Power Quality Analysis:

• Single-phase through 3-phase 4-wire circuit configurations
• Voltage range: 90V to 520V AC at 50/60Hz (perfect for Australian 230V/400V systems)
• Current measurement: 50mA to 5,000A (using appropriate Hioki clamp sensors sold separately)
• Harmonic analysis up to 13th order for identifying power quality issues
• Total harmonic distortion (THD) measurement for assessing waveform purity
• Power factor monitoring with lag/lead indication

Key Measurement Parameters: The PW3365 displays all the power parameters you need for comprehensive energy analysis: voltage (RMS and fundamental), current (RMS), active power, reactive power, apparent power, power factor (true or displacement), frequency, phase angle, and cumulative energy consumption. For demand monitoring, it tracks active and reactive power demand in user-defined intervals, essential for identifying peak loads and understanding utility demand charges.

Critical for Australian Energy Audits: When conducting facility energy assessments required for NABERS ratings, ESG reporting, or simple cost reduction initiatives, you need accurate data on actual power consumption, not nameplate estimates. The PW3365 logs this data continuously on SD cards (up to 8GB), providing months of detailed trend data showing exactly when and where energy is consumed. This long-term logging capability transforms one-time spot checks into comprehensive consumption profiles.

Quick Setup Eliminates 3-Phase Measurement Mistakes

Anyone who’s attempted 3-phase power measurement knows the challenge: six different wiring configurations, multiple leads to track, and one wrong connection that invalidates your entire dataset. The PW3365’s Quick Setup wizard walks you through the process step-by-step:

1. Select your circuit configuration (single-phase, 3-phase 3-wire, 3-phase 4-wire)
2. Follow on-screen diagrams showing exactly where to connect each sensor
3. Verify connections—the logger checks for errors and displays FAIL if connections are incorrect
4. Start logging with confidence that data will be accurate

This guided setup is particularly valuable when training new technicians or when working on unfamiliar equipment configurations. The instrument essentially becomes a measurement checklist, reducing the likelihood of test errors that waste time and produce questionable data.

Harmonic Analysis for Modern Power Systems

Australian commercial buildings and industrial facilities increasingly rely on variable frequency drives (VFDs), LED lighting, server equipment, and renewable energy inverters—all sources of harmonic distortion that traditional power monitoring overlooks. The PW3365’s harmonic measurement (up to 13th order) identifies these issues:

• 5th and 7th harmonics are the primary culprits in power quality problems, causing transformer overheating, neutral conductor overloading, and motor vibration
• Total Harmonic Distortion (THD) quantifies overall power quality, critical for compliance with AS/NZS 61000 standards
• Harmonic content display shows both numerical lists and graphical representations, making it easy to spot problem frequencies

For solar installers, harmonic analysis verifies that inverter output meets Australian grid connection requirements (AS 4777.2). For facility managers, it identifies equipment causing power quality issues before they trigger failures or increase losses.

Data Management That Actually Works on Job Sites

Power loggers live or die on their ability to capture data reliably and deliver it in usable formats. The PW3365 handles this through multiple approaches:

On-Board Storage:

• SD/SDHC memory cards up to 8GB capacity
• Internal memory backup (approximately 320KB)
• Configurable logging intervals from 1 second to 60 minutes
• Months of continuous data capture on a single SD card

Flexible Data Intervals: Save intervals of 1/2/5/10/15/30 seconds or 1/2/5/10/15/20/30/60 minutes mean you can balance data resolution against storage capacity. For short-term troubleshooting, log at 1-second intervals to catch transient events. For long-term energy audits, 15 or 30-minute intervals provide sufficient detail while maximizing storage duration.

Multiple Connectivity Options:

• LAN interface for remote monitoring and data download
• USB 2.0 for direct computer connection and data transfer
• SD card removal for simple file transfer to any computer
• HTTP server function allows web browser access to real-time data

The free HIOKI SF1000 software (downloadable) converts logged data into trend graphs, daily/weekly/monthly reports, and export formats for further analysis. For more comprehensive analysis, the optional SF1001 application provides advanced harmonic analysis, custom report generation, and multi-logger data compilation.

Built for Australian Conditions and Real-World Use

Compact Yet Rugged Design: Dimensions of 180mm (W) × 100mm (H) × 48mm (D) make the PW3365 compact enough to fit into crowded electrical cabinets or carry in a tool bag. The slim profile means it can be mounted inside panels or placed on equipment enclosures without consuming valuable space.

Flexible Power Options:

• Standard operation: Z1008 AC adapter (included) for bench or cabinet mounting
• Battery operation: Optional PW9002 battery set provides approximately 3 hours of portable operation
• Continuous charging: Battery charges while connected to AC power, whether instrument is on or off

Environmental Resilience: Operating temperature range from 0°C to 40°C with storage down to -10°C to 50°C suits Australian climates from Darwin’s tropical heat to Melbourne’s cool winters.

Measurement Update Speed: Approximately 0.5 second measurement update rate (except during SD card access or communications) provides near-real-time monitoring for observing load variations and power fluctuations.

Critical Measurement Accuracy for Professional Applications

When you’re making equipment purchasing decisions, verifying contractor work, or producing compliance documentation, measurement accuracy determines whether your data is defensible. The PW3365 delivers professional-grade accuracy:

Combined System Accuracy (PW3365 + PW9020 Voltage Sensors + Hioki Clamp Sensors):

• Voltage: ±1.5% rdg. ±0.2% f.s.
• Current: ±0.3% rdg. ±0.1% f.s. (plus clamp sensor accuracy)
• Active Power: ±2.0% rdg. ±0.3% f.s. (at unity power factor, plus clamp sensor accuracy)

These specifications mean your power consumption measurements are reliable enough for:

• Energy audit reports requiring third-party verification
• Baseline and verification (M&V) protocols for energy performance contracts
• Utility billing validation and demand charge analysis
• Equipment commissioning and performance verification
• AS/NZS 3000 electrical installation compliance documentation

Compatible Clamp Sensors for Every Application

The PW3365 requires separate AC current clamp sensors (with BNC connectors) to complete measurements. This flexibility allows you to configure the logger for specific measurement ranges:

Hioki Compatible Clamp Sensors (sold separately):

• 9660 Series – 100A AC, compact design for circuit-level monitoring
• 9661 Series – 500A AC, ideal for distribution panel and feeder monitoring
• 9669 Series – 1,000A AC, suitable for large equipment and main switchboards
• CT6843/CT6844 – 500A/5,000A AC flexible current sensors for tight spaces or irregular conductor shapes
• 9694/9695-02 – High-precision sensors for critical accuracy applications

This sensor flexibility means a single PW3365 logger can be redeployed across vastly different applications—from monitoring individual branch circuits at 10A to logging main incomer feeds at several thousand amperes.

Who Benefits Most from the PW3365

Energy Consultants & Auditors: Conduct NABERS, Green Star, or Building Performance Index assessments with comprehensive, defensible data. The non-contact sensors mean you can install logging equipment quickly without disrupting building operations or requiring electrical contractor support for every test point.

Electrical Contractors: Verify new installation performance, diagnose power quality complaints, and demonstrate compliance with Australian electrical standards. The measurement accuracy and harmonic analysis provide evidence-based troubleshooting rather than guesswork.

Facility & Building Managers: Monitor critical equipment loads, track energy consumption trends, validate energy-saving initiatives, and identify opportunities for demand reduction. The long-term logging capability reveals patterns invisible in utility bills.

Industrial Maintenance Teams: Baseline motor and process equipment power consumption, detect developing faults through power signature analysis, and schedule maintenance based on actual condition rather than arbitrary intervals.

Solar & Renewable Energy Installers: Verify inverter performance, confirm grid export limits, measure harmonic content for AS 4777.2 compliance, and demonstrate system output for commissioning reports.

Australian Standards Compliance & Safety

The PW3365 supports measurement and verification activities related to:

• AS/NZS 3000:2018 – Electrical installations (wiring rules)
• AS/NZS 61000 series – Electromagnetic compatibility (EMC) power quality standards
• AS 4777.2 – Grid connection of energy systems via inverters
• AS/NZS 3008.1.1 – Selection of cables (conductor sizing verification)

Safety ratings ensure the instrument and sensors meet Australian requirements for work on energized systems, though proper electrical safety procedures and qualifications remain essential even with non-contact sensors.

What’s Included vs. What You’ll Need

Standard Package Includes:

• PW3365 main unit
• PW9020 voltage sensors (4 pieces for 3-phase 4-wire measurement)
• Z1008 AC adapter
• USB cable
• Spiral tubes for cable organization
• Instruction manual

Required Separately (Not Included):

• AC current clamp sensors – Select appropriate Hioki clamps for your measurement range
• SD memory cards – Use only Hioki SD cards (Z4001 2GB or Z4003 8GB) for guaranteed compatibility
• Optional battery set – PW9002 for portable operation
• Carrying case – C1005 soft case for transport and storage

Important Note: The PW3365 by itself does NOT measure current or power. You must add appropriate clamp sensors to enable complete power measurement functionality. This modular design provides flexibility but requires planning when specifying equipment for specific applications.

Technical Support & After-Sales Service

As an authorized Australian reseller of HIOKI test equipment, we provide:

• Technical specification assistance for application-specific requirements
• Sensor selection guidance based on your measurement needs
• Access to calibration services maintaining measurement accuracy and compliance
• Technical support for configuration, setup, and troubleshooting
• Firmware updates and software downloads for enhanced functionality

Why Choose the PW3365 Over Other Power Loggers

Safety: World’s first completely non-metallic contact power meter—eliminates short-circuit risk fundamentally, not just through careful procedures.

Versatility: From single-phase 230V circuits to 3-phase 4-wire 400V systems, one instrument handles the full range of Australian electrical installations.

Accuracy: Professional-grade measurement specifications suitable for compliance documentation, commissioning reports, and energy performance contracts.

Data Capacity: Months of continuous logging on affordable SD cards—capture seasonal variations and long-term trends, not just spot measurements.

Ease of Use: Quick Setup wizard eliminates connection errors; on-screen graphs and statistics provide immediate insight without downloading data.

Harmonic Analysis: Identify power quality issues from VFDs, LED lighting, and inverters that traditional meters miss completely.

Proven Reliability: HIOKI’s reputation for quality test equipment trusted by electrical professionals globally, backed by Australian technical support.

Real-World Applications Across Industries

Commercial Building Energy Audits: Deploy multiple PW3365 loggers across a building’s electrical distribution—main incomer, major tenant meters, HVAC systems, lighting panels—to create a complete energy balance. The data reveals where energy actually goes versus where it’s supposed to go according to design specifications.

Industrial Process Monitoring: Track power consumption of production machinery during different operational modes. Identify idle consumption, inefficient startup sequences, and equipment that draws excessive power compared to similar units.

Solar Farm Verification: Monitor individual inverter strings to identify underperforming sections, log power quality to ensure grid compliance, and validate production against contractual guarantees.

Data Centre Power Monitoring: Measure power factor, harmonic content, and load balance across UPS systems, PDUs, and IT equipment racks. Use demand data to optimize backup generator sizing and UPS capacity planning.

Retail Chain Energy Management: Deploy identical measurement configurations across multiple store locations to benchmark energy use per square meter, identify outlier sites with maintenance needs, and verify that efficiency retrofits deliver promised savings.

Get Started With Confidence

The transition from traditional power measurement to non-contact technology represents both a safety improvement and a capability enhancement. For Australian electrical professionals tired of the risks and hassles of conventional power testing, the PW3365 offers a better approach.

Whether you’re conducting your first energy audit or your thousandth commissioning test, having measurement equipment that prioritizes your safety while delivering the data quality you need makes every job simpler. The PW3365’s combination of innovative safety technology, comprehensive measurement capability, and practical usability creates a tool you’ll reach for again and again.

Ready to eliminate short-circuit risk from your power testing workflow while gaining better data and faster setup? The HIOKI PW3365 is ready to test right out of the box.

TECHNICAL SPECIFICATIONS

Practical Significance: These specifications mean the PW3365 handles every common Australian electrical installation from standard 230V single-phase circuits through to 400V 3-phase industrial systems, with measurement accuracy suitable for compliance documentation and energy performance verification. The harmonic analysis capability addresses modern power quality issues from LED lighting, VFDs, and renewable inverters that basic power meters cannot detect.

The post HIOKI PW3365 Power Logger | Non-Contact 3-Phase Measurement appeared first on rapid-tech.

Electrical contractors, maintenance teams, and facility managers across Australia face a critical challenge: proving electrical system performance and energy efficiency without disrupting operations. Traditional handheld meters give you a snapshot—but what happens over time?

How do you document power demand patterns for an entire site? How do you prove that solar installations are performing to specification, or that industrial equipment is running efficiently? Without documented evidence, you’re left guessing about power quality, demand spikes, and energy waste. You need continuous, site-wide monitoring that creates audit trails for compliance, diagnosis, and optimization—without requiring dedicated IT infrastructure or constant manual readings.

SOLUTION OVERVIEW

The HIOKI PW3360-20/500 Kit delivers continuous, automated power monitoring that transforms how you approach energy audits, compliance documentation, and system diagnostics. Instead of snapshot readings, you capture detailed power data across hours, days, or weeks—stored directly on SD cards for later analysis and reporting. The integrated 500 A clamp sensors eliminate the need for separate equipment orders; everything you need is included and ready for deployment on Australian electrical systems.

This compact 550 g logger fits into confined plant rooms and ceiling cavities, making it practical for real-world job sites where access is limited. The QUICK SET feature walks you through 3-phase connections step-by-step, preventing the wiring mistakes that compromise data accuracy. HIOKI’s robust design handles typical Australian site conditions—industrial vibration, temperature fluctuations, and high-use environments—while maintaining ±0.3% measurement accuracy.

Whether you’re proving solar system performance under AS/NZS 5033, documenting industrial energy baseline for efficiency programs, or verifying power factor compliance across facility circuits, the PW3360-20/500 provides defensible, traceable evidence.

KEY BENEFITS & FEATURES

• Continuous Multi-Phase Monitoring That Captures Real Patterns Unlike spot checks, the PW3360-20/500 logs voltage, current, power, and demand simultaneously across three channels. You see actual consumption patterns, not averages. For solar installers verifying system integration into grid-connected properties, this means documenting instantaneous power injection and demand interaction—critical data under AS/NZS 5033. For facility managers, it reveals demand peaks that inform capacity planning and efficiency opportunities.
• 500 A Clamp Sensors—Everything Included, No Separate Orders The kit includes full-capacity 9661 clamp sensors up to 500 A, eliminating the frustration of incomplete equipment and unexpected costs. You mount the logger once, then monitor multiple circuits or phases without repositioning the base unit. The multicolored clips and spiral tubes keep everything organised on site, reducing setup time and improving measurement accuracy.
• 3-Phase Capability for Real Australian Industrial Sites Single-phase equipment matters, but most Australian industrial and commercial properties run 3-phase circuits. This logger simultaneously captures all three phases, giving you complete system visibility. No guesswork. No jumping between measurements. Complete load distribution data in one session.
• Data Logging That Creates Compliance Audit Trails Store months of raw data on the included 2 GB SD card. Access real-time and historical graphs on the 3.5″ color display, or transfer data to your computer via USB/LAN for professional reporting and analysis. The GENNECT One SF4000 software (included) transforms raw data into graphs and reports suitable for compliance documentation, client handover, and internal analysis.
• Engineered for Australian Field Conditions At just 550 g, it’s portable enough to carry between job sites yet robust enough for harsh industrial environments. The compact design (180 mm × 100 mm × 48 mm) fits into spaces where bigger equipment can’t reach—crucial in retrofit projects and confined plant rooms. Battery operation (6 hours continuous) or AC power gives you flexibility on sites with variable power availability.
• Wiring Check & QUICK SET—Eliminates Setup Errors Three-phase connections are straightforward once you understand the logic, but mistakes happen. HIOKI’s on-screen QUICK SET guides you through connections, and the wiring check function flags errors before measurement begins. This small feature has prevented countless days of wasted effort from corrupted data.

 APPLICATIONS & USE CASES

Solar Installation Performance Verification (AS/NZS 5033 Compliance) Installers must document system performance and grid interaction. The PW3360-20/500 logs real-time power injection, voltage stability, and phase balance over days or weeks—providing the evidence of compliant operation required by standards and insurance. Compare baseline grid consumption against post-installation data to prove system contribution and customer benefit.

Industrial Energy Audits & Efficiency Programs Facility managers identify where energy is wasted—often in demand peaks and power factor issues. This logger captures demand profiles across all phases over extended periods, revealing patterns that spot checks miss. Armed with actual data, you negotiate better supply contracts, justify equipment upgrades, or prove energy savings post-efficiency intervention.

Power Quality Investigation on Critical Circuits When equipment fails prematurely or behaves erratically, power quality often plays a hidden role. Log voltage stability, frequency variation, and harmonic content (with PW3360-21 option) to diagnose whether site conditions are contributing to failures. This data supports warranty claims and informs maintenance strategies.

Load Distribution & Electrical Compliance Testing Commercial buildings must prove balanced load across phases under AS/NZS 3000. The simultaneous 3-phase logging shows actual distribution and identifies circuits contributing to imbalance, enabling remedial rewiring or load rebalancing documentation.

Preventive Maintenance & Baseline Establishment Before critical equipment fails, establish a power consumption baseline. Regular logging detects gradual changes—a sign of motor degradation, bearing wear, or control system drift—allowing planned maintenance before failure.

We’re not just resellers; we’re Australian electrical professionals who understand your challenges. We stock this kit because we use it on our own projects—energy audits, compliance documentation, solar integration verification, and industrial troubleshooting.

Unlike general tool suppliers, we know the Australian electrical standards that matter to your work: AS/NZS 3000, AS/NZS 5033, AS/NZS 3760. We don’t sell you a kit and hope you figure it out. Our team provides guidance on application selection, troubleshooting, and data interpretation.

We offer fast Australian delivery and local technical support. If you need advice on sensor selection, software integration, or how to structure your testing methodology, we’re here. We’ve invested in HIOKI relationships to ensure you get genuine products, legitimate warranties, and access to firmware updates and software tools.

The PW3360-20/500 is an investment in documentation, compliance, and confidence. We want to ensure it delivers results on your specific projects.

The post HIOKI PW3360-20/500 Power Logger Kit – 500A 3-Phase Energy Audits appeared first on rapid-tech.

The post HIOKI LR8431-20 Data Logger | 10-Channel Industrial Testing appeared first on rapid-tech.

The Power Quality Problems Costing Australian Industry Thousands

Power quality issues don’t just trip breakers – they destroy equipment, halt production, and rack up costs in downtime and repairs. Electrical contractors and facility maintenance teams across Australia face the same challenge: intermittent faults that are impossible to catch without the right monitoring equipment.

Voltage dips from switching operations damage sensitive electronics. Harmonic distortion from variable speed drives overheats transformers. Transient spikes from lightning or switching events destroy control systems. Without proper power quality analysis, you’re troubleshooting blind – replacing components without understanding the root cause.

The stakes are even higher when compliance is on the line. Whether you’re commissioning solar installations, certifying industrial systems, or verifying power supply quality for critical infrastructure, you need measurement data that stands up to engineering scrutiny and regulatory standards.

How the Hioki PQ3198 Solves Your Power Quality Challenges

The Hioki PQ3198 Power Quality Analyzer is built for professionals who need accurate answers, not guesswork. This three-phase analyzer combines comprehensive monitoring capabilities with genuine compliance certification – meeting IEC 61000-4-30 Edition 3 Class A standards for power quality measurement.

Here’s what sets this analyzer apart: it captures everything simultaneously. While recording trend data for long-term monitoring, it’s simultaneously watching for voltage swells, dips, interruptions, harmonics, flicker, and transient spikes up to 6000V. When an anomaly occurs, it captures the waveform with 2 MHz sampling – giving you the forensic detail needed to pinpoint causes.

The PQ3198’s dual-circuit capability is particularly valuable for Australian solar and EV infrastructure work. Measure both the AC input and DC output of an EV rapid charger simultaneously, or monitor inverter efficiency across primary and secondary circuits – all from a single instrument. The isolated fourth channel eliminates the need for multiple analyzers on complex jobs.

What really makes this analyzer trade-ready is how Hioki handles current sensing. The PQ3198 powers sensors directly – no external power supplies cluttering your setup. Connect any Hioki current sensor from 500mA to 6000A, and the analyzer automatically detects the sensor type and range. The built-in wiring check verifies your connections before you start recording, catching setup errors before they cost you time.

Key Benefits & Professional Applications

Compliance-Ready Certification You Can Trust

The PQ3198’s IEC 61000-4-30 Class A certification isn’t just a label – it’s your assurance that measurement data meets international standards for power quality assessment. This matters when you’re producing reports for engineers, submitting compliance documentation, or defending findings against warranty claims. The analyzer’s ±0.1% voltage accuracy and gapless continuous recording mean your data holds up under scrutiny.

For Australian solar installers, this certification is essential for grid connection approvals. The PQ3198 also evaluates power supply quality against EN 50160 standards using the included PQ ONE software, automatically generating compliance reports that document voltage characteristics, frequency variations, and harmonic limits.

Capture the Events Others Miss

Transient voltage spikes lasting just microseconds can destroy equipment – but only if you can measure them. The PQ3198 captures transient voltages up to 6000V peak with 0.5 μs resolution, recording the fast-acting events that standard power meters simply can’t see. This capability is critical when investigating lightning damage, breaker operations, or unexplained equipment failures in industrial facilities.

The analyzer stores up to 9999 power quality events with complete waveform data, building a comprehensive history of power supply disturbances over weeks or months. Each event includes context – trend data showing what was happening before, during, and after the anomaly. This forensic detail transforms troubleshooting from educated guessing into data-driven problem solving.

High-Order Harmonic Analysis for Modern Power Systems

Today’s variable frequency drives, switch-mode power supplies, and renewable energy systems generate harmonic distortion well beyond the traditional 50th order limit. The PQ3198 measures supraharmonics from 2 kHz to 80 kHz – capturing the high-frequency noise that overheats motors, trips protection devices, and interferes with communications systems.

This extended frequency range is particularly valuable for analyzing solar inverters and EV charging infrastructure, where switching frequencies create harmonic content above 20 kHz. The analyzer also calculates K-Factor for transformer derating – giving facility managers the data needed to prevent transformer failures from harmonic overload.

Two-Circuit Measurement for Complex Systems

Most power quality work involves more than simple three-phase monitoring. The PQ3198’s isolated fourth voltage channel enables simultaneous measurement of two separate circuits – measuring both input and output of inverters, UPS systems, or transformers without needing multiple instruments.

For solar installers, this means verifying inverter efficiency while monitoring grid connection quality from a single setup. For EV infrastructure work, measure the AC supply quality and DC output characteristics of rapid chargers in one test session. The analyzer calculates efficiency between circuits automatically, documenting system performance for commissioning reports.

Simple Setup, Professional Results

Hioki understands that time on site costs money. The PQ3198’s preset configurations eliminate complicated parameter setup – just select your application (general monitoring, EN 50160 compliance, solar PV, or inverter measurement) and the analyzer configures recording parameters automatically.

The wiring guide displays connection diagrams for single-phase, three-phase, and dual-circuit applications directly on the 6.5-inch color screen. Once connected, the automatic wiring check verifies your setup, identifying reversed phases or missing connections before you start recording. This built-in verification catches the setup errors that otherwise waste hours of measurement time.

Long-Term Monitoring Without Gaps

Power quality issues don’t run on your schedule. The PQ3198 records continuously for up to one year with gapless data – no missed samples, no time gaps in trend data. This continuous recording capability is essential for capturing intermittent problems that occur weekly or monthly rather than daily.

Battery operation extends recording beyond mains power availability, running for up to 180 minutes on the included rechargeable pack. For permanent monitoring installations, the optional waterproof enclosure (IP65 rated) enables outdoor deployment in harsh Australian conditions.

Technical Specifications

Real-World Applications Across Australian Industries

Solar Installation Commissioning & Troubleshooting

Grid-connected solar systems require power quality verification for network approval and warranty compliance. The PQ3198 documents inverter output characteristics, harmonic content, and voltage regulation – generating the compliance reports that network operators require for connection approvals.

When solar installations experience unexplained shutdowns or grid export limiting, the PQ3198’s long-term monitoring identifies the cause. Capture the exact conditions triggering anti-islanding protection or overvoltage shutdowns, then use the waveform data to determine whether the issue lies with the inverter, transformer, or network supply.

Industrial Equipment Reliability & Maintenance

Manufacturing facilities lose thousands per hour when equipment fails unexpectedly. The PQ3198 helps maintenance teams move from reactive repairs to predictive maintenance – identifying power quality issues before they cause equipment damage.

Install the analyzer on critical motor control centers or process equipment, then review the recorded events to identify patterns. Voltage dips from crane operations, harmonic distortion from VFDs, or transient spikes from capacitor switching – whatever’s stressing your equipment, the PQ3198 captures the evidence needed to implement solutions.

EV Charging Infrastructure Certification

Electric vehicle rapid chargers draw significant power while maintaining strict quality requirements for the DC output feeding vehicles. The PQ3198’s dual-circuit capability verifies both AC supply quality and DC output characteristics simultaneously – documenting charger performance for commissioning and ongoing compliance.

This dual measurement capability also calculates overall charger efficiency, providing the data required for energy management reporting and utility demand response programs.

Data Center & Critical Infrastructure Monitoring

Data centers and critical facilities require continuous power quality assurance. Deploy the PQ3198 on UPS inputs and outputs to verify that backup power systems maintain quality during grid disturbances. The analyzer’s EN 50160 compliance checking automates the ongoing verification that power supply quality meets the standards required for sensitive IT equipment.

The optional GPS synchronization enables coordinated monitoring across multiple locations – capturing simultaneous events that affect distributed infrastructure and identifying whether power quality issues originate upstream or within specific facilities.

Building Services & Switchboard Testing

Electrical contractors troubleshooting lighting flicker, unexplained circuit breaker trips, or overheating transformers need forensic-quality power data. The PQ3198 documents the power quality characteristics that standard testing equipment can’t measure – voltage unbalance, harmonic distortion, neutral current, and flicker severity.

The analyzer’s preset configurations and automatic wiring verification mean even complex three-phase measurements are set up correctly first time. Generate professional reports directly from the included PQ ONE software – providing clients with clear documentation of findings and recommended solutions.

Why Choose Test Equipment Australia for Your Hioki PQ3198

Genuine Hioki Partnership & Local Support

We’re an authorized Hioki distributor, supplying genuine equipment backed by Hioki’s international warranty. Unlike gray imports, your PQ3198 comes with full Australian support, calibration services, and firmware updates. When you need technical guidance on applications or measurement setup, you’re talking to engineers who understand both the equipment and Australian power systems.

Calibration Services You Can Trust

Power quality measurements are only as good as the calibration behind them. Our NATA-accredited calibration laboratory services Hioki analyzers to manufacturer specifications, with calibration certificates traceable to national standards. We understand the compliance requirements for test equipment used in statutory testing and can coordinate calibration schedules that keep your instruments certified without disrupting your work schedule.

Current Sensor Selection Expertise

The PQ3198’s flexibility means choosing the right current sensors for your applications. We help you select from Hioki’s range of clamp sensors (60A to 600A), flexible Rogowski coils (up to 6000A), and AC/DC sensors for mixed current applications. Whether you’re monitoring motor circuits, solar inverters, or building switchboards, we’ll spec the sensor combination that gives you accurate measurements within budget.

Ready-to-Use Kits & Custom Configurations

The PQ3198 is available as the base unit (sensors ordered separately) or complete kits (PQ3198-92 or PQ3198-94) including four current sensors and accessories. Can’t decide? We’ll help you configure the right package for your typical applications – and we keep common sensors in stock for when your work scope expands.

Australian Stock, Fast Delivery

We maintain inventory in Australia, so you’re not waiting weeks for equipment to arrive from overseas. Place your order and have the PQ3198 on your bench within days – ready to deploy on that urgent troubleshooting job or scheduled commissioning work.

Frequently Asked Questions

Can the PQ3198 measure DC current for solar monitoring? Yes – when used with Hioki’s AC/DC current sensors (CT6862, CT6863, or CT6865), the PQ3198 accurately measures DC current with automatic zero compensation. This eliminates the drift issues common with Hall-effect sensors, making it ideal for solar array monitoring or EV charging applications where DC current measurement is required.

How does the PQ3198 compare to the older PQ3100 model? The PQ3198 offers significant improvements: IEC 61000-4-30 Edition 3 Class A compliance (vs. Edition 2 in the PQ3100), extended supraharmonic measurement to 80 kHz (vs. 40 kHz), direct sensor power supply eliminating external AC adapters, and the new PQ ONE software with improved reporting. If you’re working with modern inverter-based systems or require current Class A compliance, the PQ3198 is the right choice.

What’s included with the PQ3198, and what needs to be ordered separately? The base PQ3198 includes the analyzer, voltage cables, AC adapter, battery pack, SD card, carrying strap, USB cable, and PQ ONE software. Current sensors are ordered separately to match your specific applications. Alternatively, the PQ3198-92 kit includes four 600A clamp sensors, or the PQ3198-94 kit includes four 6000A flexible sensors – covering most industrial applications straight out of the box.

Can I monitor power quality remotely rather than reviewing data after the fact? Yes – the PQ3198 supports remote monitoring via the GENNECT One software over LAN connection. View real-time measurements from your office PC, receive automatic notifications when events occur, and download recorded data without visiting the site. For genuinely remote installations, the GENNECT Cloud service enables access from anywhere with internet connectivity.

Is calibration required, and how often? Like all precision test equipment, regular calibration maintains measurement accuracy. Hioki specifies annual calibration for the PQ3198, and most compliance applications require calibrated instruments with current certification. We provide NATA-accredited calibration services with fast turnaround – typically one week from receipt. We’ll also set up calibration reminders so your equipment never expires when you need it most.

Order Your Hioki PQ3198 Power Quality Analyzer Today

Stop troubleshooting power quality issues without proper data. The Hioki PQ3198 delivers the measurement accuracy, compliance certification, and comprehensive recording capability that Australian electrical contractors and facility maintenance teams depend on.

Ready to discuss your specific application or configure the right analyzer package? Contact Rapid-Tech Equipment – we’ll help you select current sensors, arrange calibration, and get your PQ3198 ready for deployment.

The post Hioki PQ3198 Power Quality Analyzer appeared first on rapid-tech.