The HT9023 can measures DC voltage up to 1500V, AC, AC+DC voltage up to 1000V, Active, Reactive and Apparent Power, Power Factor, Energy, voltage/current harmonic analysis up to the 25th with THD% calculation in balanced single-phase or three-phase systems.

With the HT Instruments HT9023 TRMS AC/DC Clamp-On Power Quality Analyzer it is also possible to carry out the phase sequence test with 1-terminal. The instrument also detects the events linked to motor starting currents (Dynamic INRUSH) and allows recording each measured electric parameter over time, with the possibility of transferring data via WiFi to Android/iOS devices through the HTAnalysis App or onto PC through the TOPVIEW software.

The HT9023 clamp is provided with a wide graphic dot-matrix screen (128x128pxl) with backlight, in order to allow reading data even in poorly lit environments, and it is provided with an auto power off function to preserve its internal battery.

The post HT Instruments HT9023 TRMS AC/DC Clamp-On Power Quality Analyzer appeared first on rapid-tech.

It is ideal instrument for the industrial electrician and for use on large solar (photovoltaic) farms with its 1500V DC function.

The clamp is provided with a display with 6000 measuring spots with backlight and bargraph to allow for a simple reading even in poorly lit environments. HT9025 also measures Resistance, Frequency, Capacity and Temperature with K-type probe.

The Bluetooth connection allows for the transfer of the saved snapshots by means of the dedicated App HTMercury.

HT Instruments HT9025 Functions

The post HT Instruments HT9025 AC / DC current clamp with DATA LOGGER function appeared first on rapid-tech.

The HT Line Splitter separates the Active (Line) from the neutral and ground wires on a standard 240VAC 10A & 15A outlet allowing current measurements to be made with a current clamp. Without the Line Splitter, the current clamp measures the load current going in both directions, effectively cancelling the measurement.

The HT Line Splitter has a standard measurement section and a x10 multiplier section for use with higher ranged clamp meters.

The HT Instruments HA000951 Line Splitter can also be used to make voltage checks safely with standard multimeter probes.

Suitable for bot 10A and 15A outlets.

HT Instruments HA000951 Line Splitter Functions:

Conductor splitting without cable stripping!

• Measure Mains voltages safely via shrouded banana sockets
• Leakage current on earth conductor
• Measurement of leakage current under RCD mode (Line-Neutral)
• Line current
• 10X magnified Line current

The post HT Instruments HA000951 Line Splitter – Separator appeared first on rapid-tech.

This instrument is guaranteed for one year against material or production defects, in accordance with our general sales conditions. During the warranty period the manufacturer reserves the right to decide either to repair or replace the product. The warranty shall not apply in the following cases: 

Repair and/or replacement of accessories and battery (not covered by warranty). 

Repairs that may become necessary as a consequence of an incorrect use of the instrument or due to its use together with non-compatible appliances. 

Repairs that may become necessary as a consequence of improper packaging. 

Repairs which may become necessary as a consequence of interventions performed by unauthorized personnel.  Modifications to the instrument performed without the manufacturer’s explicit authorization 

Use not provided for in the instrument’s specifications or in the instruction manual

Preparation for Use

Initial checks This instrument was checked both mechanically and electrically prior to shipment. All possible cares and precautions were taken to let you receive the instrument under perfect conditions. Notwithstanding we suggest you to check it rapidly (any damage may have occurred during transport – if so please contact the local distributor from whom you bought the item). Make sure that all standard accessories mentioned in § 12.2 are included. Should you have to return back the instrument for any reason please follow the instructions mentioned in § 13

HT Italia HT7003 Service

Should the instrument not work properly, make sure that battery is correctly installed and working and replace if necessary before contacting your distributor. Should you need for any reason to return back the instrument for repair or replacement take prior agreements with the local distributor from whom you bought it. Do not forget to enclose a report describing the reasons for returning (detected fault). Use only original packaging. Any damage occurred in transit due to not original packaging will be charged anyhow to the customer. The manufacturer will not be responsible for any damage to persons or things

The post HT Italia HT7003 Clamp Meter 300A AC appeared first on rapid-tech.

It also tests phase sequence and phase conformity by 1-lead measuring method as well as detects any event related to electric motor starting currents (DYNAMIC INRUSH).  DYNAMIC INRUSH™ permits to measure inrush currents with user-defined time frames, providing measurements more reliable than standard fixed time-frame testers.

The user has the chance to recall and display the measurement by applying different time frames. For example, if the user carries out a measurement using a time frame of 100 ms, he can post-process the same measurement by applying a time frame of: 16,7, 20, 50, 100, 150, or 200 ms. This enables the utmost flexibility for each measurement, and prevents to measure again and again to get the real inrush current value.

HT Italia HT9020 Clamp Meter WARRANTY CONDITIONS

This instrument is warranted against any material or manufacturing defect, in compliance with the general sales conditions. During the warranty period, defective parts may be replaced. However, the manufacturer reserves the right to repair or replace the product. The warranty shall not apply in the following cases: 

Repair and/or replacement of accessories and batteries (not covered by warranty). 

Repairs that may become necessary as a consequence of an incorrect use of the instrument or due to its use together with non-compatible appliances. 

Repairs that may become necessary as a consequence of improper packaging. 

Repairs which may become necessary as a consequence of interventions performed by unauthorized personnel.  Modifications to the instrument performed without the manufacturer’s explicit authorization. 

Use not provided for in the instrument’s specifications or in the instruction manual.

The post HT Italia HT9020 Clamp Meter with Powers/Harmonics and Inrush Currents appeared first on rapid-tech.

The HT HT 4013 Clamp Meter has been designed to measure AC/ DC current up to 400A and AC/DC voltage up to 600V to reach CAT III 600V in compliance with standard IEC/ EN61010-1.

The HT 4013 is provided with an internal sensor to detect AC voltage also without contact, through a red LED turning on. This model also carries out measurements of Resistance, Continuity tests, Frequency, Capacity, Diode test, Duty Cycle and Temperature with K-type probe, among others. The clamp is also provided with the auto power off function to preserve its own battery.

HT Italia HT4013 Function:

• AC/DC current up to 400A
• DC/AC voltage up to 600V
• “Voltsense” feature for AC voltage detection
• Resistance
• Continuity test with buzzer
• Frequency with test leads
• Capacitance
• Diode test
• Duty Cycle
• Temperature with type K probe
• Autorange
• Data HOLD
• Relative measurement
• Auto Power OFF

HT Italia HT4013 AC/DC Clampmeter Specifications:

HT Italia HT4013 Standard Accessories:

• Couple of test leads
• TK101 : Type K bead probe
• Carrying bag
• Batteries
• User manual

The post HT Italia HT4013 AC/DC 400 Amp Clampmeter appeared first on rapid-tech.

HT Italia HT100 is a professional CAT IV clamp meter with an inbuilt automatic detection function for AC True RMS current measurements of up to 200A. The model have an “open jaw” design, a large LCD display (9999 counts), a “Voltsense” voltage detection feature and a backlight to make it possible to see regardless of dim or bright lighting. The model also performs AC/DC True RSM voltage, resistance, continuity and diode test measurements. The Auto Power OFF feature extends the battery life.

HT ITALIA HT100 Functions:

• TRMS measurement
• AC current up to 200A
• DC/AC voltage up to 1000V
• “Voltsense” feature for AC voltage detection
• Resistance
• Continuity test with buzzer
• Diode test
• Autorange
• Automatic detection of functions
• CAT IV 600V, CAT III 1000V Safety Rating
• Data HOLD
• Backlight
• Auto Power OFF

HT ITALIA HT100 Standard Accessories:

• Two of test leads
• Carrying bag
• Batteries
• User manual

The post HT Italia HT100 AC TRMS 200A Clampmeter appeared first on rapid-tech.

HT Italia XL421 Functions:

• True-rms AC current measurement up to 2500A.
• Recording with sampling programmable period.
• Manual activation of recording.
• Low battery indication.
• LED indication of any operation.
• RS-232 interface.
• Data maintained without batteries.
• Programming with DATALINK software.

Included Accessories

• Inbuilt/integrated 3000 amp flexible current clamp, type HTFLEX33DL.
• RS-232 serial cable, type C2004.
• Adhesive Velcro for fixing.
• Carrying bag, type BORSA2000.
• User’s manual.

The post HT Italia XL421 True-Rms AC Single-Phase Current Logger appeared first on rapid-tech.

The HT Italia XL422 performs measurements and records TRMS AC current up to 2500A in a generic three phase 3-wire system.

The XL422 is part of the HT Data Logger family which includes the following models: XL421, XL423 and XL424

These models can perform measurements and recordings of TRMS AC current up to 2500A from a generic single-phase system.

They can be very useful for various applications:

• evaluation of load consumption
• verification of nominal power of the incoming supply

The instrument is enclosed in a safe and practical case with a built-in flexible clamp enabling you to clamp-on to a cable or bar with wide dimensions.

Thanks to a sophisticated memory algorithm the instrument is able to record for a considerable time, up to about 1 year! (With a 60 sec integration period for single phase loggers and 5 min integration for 3 phase loggers dependant on battery life). It is also simple and straight forward to use.

With TOPVIEW2004 Windows software, supplied with the model, it’s possible to download and analyse all recorded data directly on your PC.

The high-protection (IP65) casing makes the instrument reliable to use in extreme environmental conditions.

HT Italia XL422 Function:

• TRMS AC current measure up to 2500A
• Recording with sampling programmable period
• Manual activation of recording
• Low battery indication
• LED indication of any operation
• RS-232 interface
• Data maintaining without batteries
• Programming with software

The post HT Italia XL422 3-Phase Current Datalogger appeared first on rapid-tech.

Specifications

The post HT Italia HT9021 1000A AC/DC True-Rms CAT IV 600V Clampmeter with Temperature Measurement appeared first on rapid-tech.