Accessories Archives - rapid-tech https://rapid-tech.com.au/accessories-gw-instek/ Test Equipment Supplier Fri, 27 Jun 2025 07:20:19 +0000 en-AU hourly 1 https://wordpress.org/?v=6.9.10 https://rapid-tech.com.au/wp-content/uploads/2023/11/cropped-Rapid-Tech-logo-blue-1-1-32x32.png Accessories Archives - rapid-tech https://rapid-tech.com.au/accessories-gw-instek/ 32 32 GW Instek GIT-5060 Isolated Transformer https://rapid-tech.com.au/gw-instek-git-5060-isolated-transformer/ Mon, 23 Nov 2020 03:42:59 +0000 https://rapid-tech.com.au/?post_type=product&p=17011

The GIT-5060 features a 900VA operation capacity, 5A current limit and a built-in air switch. It is ideal for conduction measurements and avoiding dangerous conditions.

  • For actual measurements, isolated transformers are always needed to avoid dangerous conditions
  • 900VA operation capacity
  • Input voltage frequency  50~60Hz
  • Max. current  4A
  • Max. voltage  250V
  • 5A current limit with a built-in air switch
  • Able to meet most measurement requirement

    GIT-5060 User Manual

The post GW Instek GIT-5060 Isolated Transformer appeared first on rapid-tech.

]]> The GW Instek GIT-5060 Isolated Transformer for GLN-5040A is able to meet most measurement requirements. The GIT-5060 features a 900VA operation capacity, with a 5A current limit and a built-in air switch. It is ideal for conduction measurements and avoiding dangerous conditions.

GW Instek GIT-5060 Features

  • EMI testing
  • 900VA operation capacity
  • 5A current limit with a built-in air switch
  • Able to meet most measurement requirements

The post GW Instek GIT-5060 Isolated Transformer appeared first on rapid-tech.

]]> GW Instek GLN-5040A Line Impedance Stabilisation Network https://rapid-tech.com.au/gw-instek-gln-5040a-line-impedance-stabilisation-network/ Mon, 23 Nov 2020 02:40:02 +0000 https://rapid-tech.com.au/?post_type=product&p=17007

The GLN-5040A Two Line V-Network is used for EMI testing for EMI/EMC Pre-Compliance. It provides stable impedance for the EUT terminals and the reference ground within the conducted emissions range.

The GLN-5040A also isolates the unwanted network signals from the power supply unit and only couples the disturbance voltage of the measuring device to the receiver

  • Suitable for signal phase device conduction
  • Isolates the unwanted network signals
  • High pass filter selection function
  • Provides stable impedance for the EUT terminals and the reference ground

    GLN 5040A User Manual

The post GW Instek GLN-5040A Line Impedance Stabilisation Network appeared first on rapid-tech.

]]> The GW Instek GLN-5040A Line Impedance Stabilization Network is used for EMI testing. It provides a stable impedance for the EUT terminals and the reference ground within the conducted emissions range.

The GW Instek GLN-5040A Two Line V-Network is used for EMI testing. It provides a stable impedance for the EUT terminals and the reference ground within the conducted emissions range. The GW Instek GLN-5040A also isolates the unwanted network signals from the power supply unit and only couples the disturbance voltage of the measured device to the receiver.

The GW Instek GLN-5040A performance is in compliance with the standard requirements of CISPR16-1-2 for V-networks with a simulated impedance of 50μH + 5 Ω) || 50 Ω in the frequency range of 9kHz to 30MHz.

The GLN-5040A uses standard BNC output connector with 50 Ω output impedance to match any measurement devices such as receivers and spectrum analyzers.

It is equipped with an artificial hand function that simulates a handheld type measurement, a 9kHz and 150kHz high pass filter selection function that allows the product to select the correct filters according to the relevant standard.

The GLN-5040A is also suitable for signal phase device conduction (disturbance voltage) measurement. Due to design principles, there may exist a great deal of leakage current. It is recommended that the unit is grounded when used, and if necessary, it should also be used with an isolation transformer.

Features

  • EMI testing for EMI/EMC Pre-Compliance
  • Provides stable impedance for EUT terminals and reference ground within conducted emissions range
  • Isolates unwanted network signals from power supply unit
  • Only couples disturbance voltage of measured device to receiver
  • In compliance with standard requirements of CISPR16-1-2
  • Uses standard BNC output connector with 50 ohm output impedance
  • Matches any measurement devices such as receivers and spectrum analyzers
  • Equipped with artificial hand function that simulates handheld type measurement
  • 9kHz and 150kHz high pass filter selection function that allows product to select correct filters according to relevant standard
  • Suitable for signal phase device conduction (disturbance voltage) measurement

Applications

  • Laboratories
  • Production/Manufacturing
  • Workshops
  • Research and Development

The post GW Instek GLN-5040A Line Impedance Stabilisation Network appeared first on rapid-tech.

]]>